Protegra CS PRO RO EDI 125 - Reverse Osmosis System with Ionpure EDI, 125 l/h

Protegra CS PRO RO EDI 125 Reverse Osmosis System with Ionpure EDI CONSISTENTLY HIGH WATER QUALITY The Protegra CS® Pro RO EDI system is a high-performance purification solution for deionised water applications. Featuring industry-leading reverse osmosis technology and a high-performance Ionpure® CEDI cell, the system maintains water quality at the required standard. The system is ideal for a range of laboratory and industrial applications with a typical water quality of > 0.07µS/cm and a flow rate up to 125 l/h at 15°C. Product features and benefits: - Energy efficient and high performance reverse osmosis (RO) modules effectively achieve high inorganic retention and permeate production. This reduces energy demand and minimizes water waste. - Electro-deionization removes the residual salt content from the water without exhausting itself. - Automatic rinsing of entire system before going into stand-by mode reduces build-up of ions in the RO membranes - increasing the lifespan. - Microprocessor control provides automatic operation with continuous monitoring of all important parameters. - The limits for conductivity and flow rates of pure water can be set individually. - Removable front and side panels for easy service access. - The system is low maintenance. Production of pure water: Reverse osmosis - Feed water solenoid valve - Pressure regulator - Conductivity sensor for feed water (cell constant C=0,1) - Filter with activated carbon - Pressure switch for feed water - Stainless steel pump (1.4401/1.4301) - Pressure sensor for operating pressure - 1 Reverse osmosis module made of polyamide/polysulfone with pressure tubes made of stainless steel (1.4571) and end caps made of polypropylene (PP) - Regulator for concentrate flow to drain and return - Three flow sensors for pure water, concentrate and brine - Conductivity sensor for permeate (cell constant C=0,2) - Quality-dependent permeate distribution valve Continuous Electrodeionization (CEDI): - Ionpure CEDI module for up to 125 l/h - Conductivity sensor for pure water, temperature compensated (cell constant C=0,1) - Temperature sensor New 7" control touch-panel: - Mounted on the front of the system - System status displayed - Conductivity of feed water, permeate and pure water - Volume flow rate of pure water, concentrate and brine - Alarm indicator - Timeline for concentrate discharge to drain and module rinsing - Multilingual (German, English) - USB interface for data transfer - microSD-Port (Data recording and firmware updates) Supplied with: - Operating manual - Electrical circuit diagram - Active carbon fine filter cartridge - key for filter cartridge - Set of 4 hoses (3m ea), 3/4" - Power cable NOT included Optional: - Water Guard R3/4" f/m (W2T828181) - LED-Signal light tower (Red-yellow-green) (W3T307039) - Modbus TCP Gateway for continuous data transfer to a BMS (Building management system) or PC/ laptop (W3T570885) - CO2 Membrane degassing (W3T262426) - Complete DQ/IQ/OQ/PQ documentation and validation of the system on site available upon request. Feed water specifications: Softened or hardness stabilized Flow rate: 180 - 260 l/h Pressure: 2,5 - 6,0 bar Temperature: 5 - 30°C Conductivity: < 1400 µS/cm Colloid index (SDI): < 3 TDS: 700 mg/l CO2: < 10 mg/l SiO2: < 10 mg/l TOC: < 1500ppb pH: 3-9 Total iron: < 0.1 mg/l Free chlorine: < 0.1 mg/l Manganese: <0,05 mg/l Performance specifications: Flow rate at 15 °C: 125 l/h Conductivity: < 0.1 µS/ml Typical conductivity: < 0.07 µS/ml Recovery rate up to: 50-80% Technical data: Mains input: 400V 3/N/PE 50-60 Hz (Power cord not included in delivery) Power consumption: 1,0 kW/h Ambient temperature: 1 - 30°C Humidity: no condensation Fuse protection: max. 16 A Residual current device (RCD formerly FI): Type B, 30mA, short-time delayed Sound pressure level: max. 64db(a) The power connection is made via supply terminals inside the Protegra and must be provided by the customer. Hydraulic ports: Feed water: G3/4" MPT Product water: G3/4" MPT Concentrate: G3/4" MPT Brine: G3/4" MPT Dimensions and weight: Height: 1795 mm (on wheels) Height w/ optional lamp: 1960 mm Width: 650 mm Depth: 545 mm Weight: approx. 165 kg Please note: The unit accepts a feed water salt concentration of 700 mg/l, equivalent to a conductivity of 1400 µS/cm at 15 °C. The feed water specifications are guidelines. The pure water specifications can only be guaranteed if a feed water analysis including levels of silicate and CO2 of the installation site and all other relevant parameters have been analyzed. more